|
Aboriginal Fire-by-Friction methods |
|
|
|
Written by Dick Baugh
|
There are at least two different methods used by the Aboriginal people
of Australia to start fires. This article describes them. Australian
Aborigines are one of the few remaining cultural groups which are still
familiar with their traditional subsistence methods.
I had always wondered what methods were used by indigenous people who
habitually start a fire by friction protected their fire sticks from
moisture. This would be particularly relevant in the Northern Territory
where 6 months out of each year there are monsoon rains on a daily
basis. On a recent trip to Australia my wife and I saw young Aboriginal
men (Remember, in Australia 'abo' is a pejorative) at the Tjakupai
Cultural Center in the Northern Territory start a fire with a hand-spun
drill. They had a nicely made little case, covered with some sort of
bark and resin and decorated with red seeds. The business end of the
spindle and the hearthboard were protected by this cover. The entire
assembly was then leaned, case up, against a tree. Only the parts which
needed protection from the elements were protected.
It was clear that most of the Aboriginal men I spoke with in the NT
were familiar with starting a fire with a hand drill. That does not
mean they were always successful. At a cultural center in Darwin, NT, I
asked a man if he had a set of traditional Aboriginal fire sticks and
was willing to trade them for a set which I had brought from
California. He went to his truck and brought out a spindle and
hearthboard but said they belonged to his cousin so they were not
available for trading. How many people keep a friction fire set in
their vehicle? Of course he had to demonstrate how they worked. He
apologized, saying that an essential ingredient was missing. He didn't
have any dried kangaroo poo to put in the notch and catch the ember. He
promptly assumed the position and stared twirling the spindle. Smoke
and sweat but no ember. I know the feeling. Then a mate of his took
over. Still no glowing ember. After a couple of blisters they gave up.
Examination of the spindle and hearthboard showed that they were made
from fairly dense wood. That means that much more energy would have to
be applied to them to achieve ignition. Lower density materials with
commensurate lower thermal capacity and conductivity require less
energy to achieve ignition. Not being the mesomorphic (muscular) type I
have to choose materials very carefully when I try to start a hand
drill fire.
In the central desert of Australia a different fire-by-friction method
is used. This was described very clearly by Richard A. Gould in his
book "Yiwara: Foragers of the Australian Desert", ISBN684-71787-5,
published in 1960 by Charles Scribner's Sons. "A branch is split and
placed on the ground and thin wedges are inserted to hold the crack
open and 'nail' the branch to the ground. One man stands astride the
branch to hold it down while another places bits of dry kangaroo dung
in the crack and lays the edge of his spearthrower across the branch at
a point directly above the dry dung. He holds one end of the spear
thrower and a third man kneels and takes hold of the other end. The two
men saw vigorously back and forth with the spearthrower, working
between the standing man's legs. In about twenty seconds a faint wisp
of smoke appears from the dung inside the crack and the men stop sawing
and begin to blow on the smoldering dung, adding bits of dry grass to
it as tinder. The faint glow spreads until the tinder is alight and the
burning tinder is carried around to light the four fires."
Lynn Weise, Monte Boyd, Emilio Lanier and I successfully started a fire
using this device, hereby dubbed the Aboriginal fire saw at one of our
Tuesday night flintknapping sessions. Lynn supplied a yucca stalk
(unknown species but fairly hard, solid) from New Mexico and I brought
a piece of split black cottonwood (Populus trichocarpa) to use instead
of a spearthrower. These materials are among the most reliable choices
for fire-by-friction with either a hand drill, bow drill or Polynesian
fire plow. We split the yucca stalk and separated the two halves with a
small wad of shredded cattail leaf. Emilio and Monte stood on either
end of the split yucca. Our initial attempt didn't work because there
was very little friction between the saw and the outer surface of the
yucca. We next cut a small notch with a knife into the yucca where the
saw rubbed back and forth. This improved the situation considerably and
there was an apparently much higher coefficient of friction. A minor
effort gave profuse smoke but no ember. The final modification was to
push the wad of shredded cattail fiber down further so it was not in
contact with the saw. Success! A moderate effort by the two sawyers
produced plenty of smoke. We saw a tiny wisp of smoke coming up from
inside the accumulation of powder. Gentle blowing caused it to get
brighter. From here it would be an easy matter to transfer it to a
handful of dry tinder and create a flame.
An alternate method, involving only two persons, would be to have the
two persons kneel on one knee on opposite sides of the split stick.
Their forward foot would be placed on the split stick to hold it
securely. In this manner two persons could simultaneously hold the
split stick down and do the sawing.
Why should one choose one fire-by-friction method over another? Better
yet, why would one group of indigenous people select a particular
method? What materials are available? What are the human resources
available? What are the climatic conditions under which they must work?
What tools are available for fashioning the parts? Beats me. The
Aboriginal fire saw requires very little in the way tools for
construction since it involves only rough cutting and splitting and no
precision operations. The method has two advantages for a classroom
situation. It is a joint effort. Consequently it can be used to teach
the advantages of teamwork and cooperation. The physical efforts of at
least two persons are combined. Consequently two people who are not
terribly muscular can achieve a friction fire when neither could do it
individually. This is important for teaching stone age skills to young
people or the weaker sex, whichever one that is. The second reason for
teaching it is that it is a method which requires no tools. Give it a
try.
Thank you to Dick Baugh at www.primitiveways.com for supplying this article
 |
Show/Hide comments
Show/Hide comment form
BushMoot, the best event of the year - from 1st -5th August 2008 at Merthyr Mawr in South Wales. 
I used Hazel wood. Choose the
thin long shoots of wood which i would think are a couple of years old.
If you don't catch anything at first don't worry. It may just be a case of
changing a few things.
Most bushcrafters know that Birch bark is fantastic for fire lighting
because of all the oil concealed within it. This tutorial guides you
through the process of extracting that tar from the bark.
Now we could bung a label on (which should always say they type of wine and when it was bottled). I suggest you cross-reference to a book of recipes and notes so that when you get a cracking wine you can recreate it. We are going to add a little something to the presentation of the wine by putting a foil cap over the neck. First we drop a foil cap (available for a couple of pence from a wine shop) over the bottle neck.
Right, we now have clean, fined and filtered wine. We pour it into clean (yes and sterilised) bottles with a funnel. We need to cork it. Its possible to put corks in with a mallet. I use a corking gun and waxed corks that do not need to be soaked (plain corks do)
Well, the finings have worked – the wine is beautifully clear.
As soon as I'd finished my Paracord Bracelet, I'd decided to write a tutorial on making one. A good thing considering the majority of the responses since I posted it were asking me how to do it! Here goes.. You will need approximately 3 metres of paracord with the ends already sealed/melted, and something to make a temporary knot - a twist tie or piece of string should suffice.
I have been asked a number of times recently to provide some advice of guidance on the best way to sharpen an axe. Whilst I am always happy to provide input, I thought that it might be worthwhile to put together a tutorial on the basic techniques. The techniques used in here are intended to provide not only a sharp axe but also a safe and efficient axe.
There was a period in my life where I lived out of a pack for months at a time and this was one of my staples.
I like to coil it like a rope on a stick and bake it over hot coals...
There are many different ways you can make a berry picker but this is just a design i came up with which uses a packet of kebab skiewers and some discs of wood.
The whole kit took less than three hours to finally pull together — though that really overlooks by far the most time-consuming aspect, the preparation of materials. In fact, preparation has two components, actually. The first is the selection of materials. The second is the actual preparation.