How to use a compass
Lesson 3 - Magnetic Declination
|
Unfortunately, sometimes, for some quite often, it is even more complicated. There is something called magnetic declination. You see, the compass is pointing towards the magnetic north pole, and the map is pointing towards the geographic north pole, and that is not the same  place. To make things even more complicated, there is on most hiking-maps something (that is very useful) called the UTM-grid. This grid doesn't have a real north pole, but in most cases, the lines are not too far away from the other norths. Since this grid covers the map, it is convenient to use as meridians.
On most orienteering maps (newer than the early 70's), this is corrected, so you won't have to worry about it. But on topographic maps, this is a problem.
First, you'll have to know how large the declination is, in degrees. This depends on where on the earth you are. Here in California it varies depending on where you are. Or somewhere on the map, it says something about it. One thing you have to remember in some areas, the declination changes significantly, so you'll need to know what it is this year.
When you are taking out a course, you will do that more or less as described in lesson 2, but this time, you must also look out so that you don't align the orienting lines with the grid lines pointing west or east, or south for that matter. When you have taken out a course like you've learned, you must add or subtract an angle, and that angle is the angle you found before you left home, the angle between the grid lines or meridians and the magnetic north.
|
The declination is given as e.g. "15 degrees east". When you look at the figure, you can pretend that plus is to the right, or east, and minus is to the left and west. Like a curved row of numbers. So when something is more than zero you'll subtract to get it back to zero. And if it is less, you'll add. So in this case you'll subtract 15 degrees to the azimuth, by turning the compass housing, according to the numbers on the housing. Now, finally, the direction of travel-arrow points in the direction you want to go. Again, be careful to aim at some distant object and off you go.
 You may not need to find the declination before you leave home, actually. There is a fast and pretty good method to find the declination wherever you are. This method has also the advantage that corrects for local conditions that may be present.
This is what you do:
- Determine by map inspection the grid azimuth from your location to a know, visible, distant point. The further away, the more accurate it gets. This means you have to know where you are, and be pretty sure about one other feature in the terrain.
- Sight on that distant point with the compass and note the magnetic azimuth. You do that by turning the compass housing so that it is aligned with the needle. You may now read the number from the housing where it meets the base of the direction of travel-arrow.
- Compare the two azimuths. The difference is the declination.
- Update as necessary. You shouldn't need to do this very often, unless you travel in a terrain with lots of mineral deposits.
There are a few riddles and rhymes to help you remember whether you should add or subtract. I don't know them. If you live in an area where you don't go far for it to change between east and west, it is so small you wouldn't need to worry about it anyway. So it's best to just remember whether you should add or subtract.
|
Uncertainty
You can't always expect to hit exactly what you are looking for. In fact, you must expect to get a little off course.
How much you get off course depends very often on the things around you. How dense the forest is, fog, visibility is a keyword. And of course, it depends on how accurate you are. You do make things better by being careful when you take out a course, and it is important to aim as far ahead as you can see.
 In normal forest conditions we say that as a rule of thumb, the uncertainty is one tenth of the distance traveled. So if it is like in the figure, you go 200 meters on course, it is possible that you end up a little off course, 20 meters or so. If you're looking for something smaller than 20 meters across, there is a chance you'll miss. If you want to hit that rock in our example you'll need to keep the eyes open!
In the open mountain areas, things are of course a lot easier when you can see far ahead of you.
|
| |
Kjetil Kjernsmo
Thanks to www.buckskin.org
 |
Show/Hide comments
Show/Hide comment form
BushMoot, the best event of the year - from 1st -5th August 2008 at Merthyr Mawr in South Wales. 
I used Hazel wood. Choose the
thin long shoots of wood which i would think are a couple of years old.
If you don't catch anything at first don't worry. It may just be a case of
changing a few things.
Most bushcrafters know that Birch bark is fantastic for fire lighting
because of all the oil concealed within it. This tutorial guides you
through the process of extracting that tar from the bark.
Now we could bung a label on (which should always say they type of wine and when it was bottled). I suggest you cross-reference to a book of recipes and notes so that when you get a cracking wine you can recreate it. We are going to add a little something to the presentation of the wine by putting a foil cap over the neck. First we drop a foil cap (available for a couple of pence from a wine shop) over the bottle neck.
Right, we now have clean, fined and filtered wine. We pour it into clean (yes and sterilised) bottles with a funnel. We need to cork it. Its possible to put corks in with a mallet. I use a corking gun and waxed corks that do not need to be soaked (plain corks do)
Well, the finings have worked – the wine is beautifully clear.
As soon as I'd finished my Paracord Bracelet, I'd decided to write a tutorial on making one. A good thing considering the majority of the responses since I posted it were asking me how to do it! Here goes.. You will need approximately 3 metres of paracord with the ends already sealed/melted, and something to make a temporary knot - a twist tie or piece of string should suffice.
I have been asked a number of times recently to provide some advice of guidance on the best way to sharpen an axe. Whilst I am always happy to provide input, I thought that it might be worthwhile to put together a tutorial on the basic techniques. The techniques used in here are intended to provide not only a sharp axe but also a safe and efficient axe.
There was a period in my life where I lived out of a pack for months at a time and this was one of my staples.
I like to coil it like a rope on a stick and bake it over hot coals...
There are many different ways you can make a berry picker but this is just a design i came up with which uses a packet of kebab skiewers and some discs of wood.
The whole kit took less than three hours to finally pull together — though that really overlooks by far the most time-consuming aspect, the preparation of materials. In fact, preparation has two components, actually. The first is the selection of materials. The second is the actual preparation.